Reset your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the settings or are experiencing unexpected performance. Fortunately, resetting your Holosun is a straightforward process that can be completed in just a few procedures.

• Begin by ensuring your red dot sight is turned on.
• Locate the small button for reset on the rear of the unit.
• Use a small object to press and hold the reset button for approximately 5 moments.
• Release the lever and your Holosun EPS Carry Red Dot sight will reboot.
• Its red dot sight should now be set back to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to its factory configuration is a breeze. First, determine the tiny button on the side of your optic. Then, sustain it for around ten seconds until you see the indicator light change. Your Holosun EPS Carry is now reverted to its factory settings, ready for consistent targeting.

Bring Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Press and hold the power button for approximately 10 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and verify your sight's functionality. If you encounter any further problems, don't hesitate to reach out to their technical assistance.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they click here will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• Initially, Turn on your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• While continue holding these buttons, tap the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to complete. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Restore your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will set back your sight to its original settings, clearing any personalized configurations you've made. To execute this reset, follow these simple steps:

• Initially, identify the reset switch on your EPS Carry.
• Then, press a fine object, like a toothpick, to push the reset lever.
• While hold the reset switch activated, turn your EPS Carry.
• It will display a message indicating that the reset is complete.

After the reset is successful, your EPS Carry will be returned to its factory settings.

Report this wiki page